Search
- My IPS AC Adapter does not power my LabPro, WDSS, or Stir Station.
- Between 8/27/08 and 9/5/08, a small number of power supplies were shipped that were defective. If you received a power supply around this time with the name ...
- https://www.vernier.com/til/1876
- Stir Station Troubleshooting and FAQs - Technical Information Library
- May 11, 2009 ... This device is not a sensor. No calibration is possible. RELATED VERNIER PRODUCTS –Microstirrer (MSTIR) –Power Supply for LabPro, WDSS, and Stir ...
- https://www.vernier.com/til/1387
- My power supply no longer works. – Technical Information Library
- Power Supply for LabPro, WDSS, and Stir Station (IPS) (For LabPro, CBL2, WDSS, and DCU.) LabQuest Power Supply (LQ-PS, discontinued) LabQuest Power Supply ...
- https://www.vernier.com/til/1911
- What (replacement) power supply should I buy for my interface or ...
- Sep 25, 2020 ... ... Supply (LQ3-PS) or the LabQuest Power Supply (LQ-PS, discontinued). LabPro (LABPRO) uses the Power Supply for LabPro, WDSS, and Stir Station (Â ...
- https://www.vernier.com/til/9618
- What power supplies can I use with the DCU? - Technical ...
- Jul 8, 2015 ... It has a 2.1 mm ID. This socket will fit the 6-volt LabPro (Power Supply for LabPro, WDSS, and Stir Station (IPS))or 9-volt ULI power supply ...
- https://www.vernier.com/til/3236
- DCU Power Output Pack (DCU-POP) Troubleshooting and FAQs ...
- Aug 6, 2018 ... ... Power Supply for LabPro, WDSS, and Stir Station (IPS) as external power supplies. Third party power supplies must be either 3.3 mm center ...
- https://www.vernier.com/til/4224
- WDSS Troubleshooting and FAQs - Technical Information Library
- Power Supply for LabPro, WDSS, and Stir Station (IPS). Published: September 16, 2019. Updated: February 7, 2025. ©2024 All rights reserved ...
- https://www.vernier.com/til/1554
- LabPro Troubleshooting and FAQs – Technical Information Library
- Oct 18, 2018 ... My IPS AC Adapter does not power my LabPro, WDSS, or Stir Station. Care and Maintenance. How do I prevent my LabPro interfaces from being stolen ...
- https://www.vernier.com/til/1613
- Digital Control Unit (DCU) Troubleshooting and FAQs - Technical ...
- Jun 4, 2018 ... ... electricity at a voltage that matches your power supply. The DCU ... Power Supply for LabPro, WDSS, and Stir Station (IPS) Digital ...
- https://www.vernier.com/til/2101
- Bluetooth Help and Troubleshooting Tips related to the Wireless Dynamics Sensor System (WDSS)
- INTRODUCTION TO BLUETOOTH WITH THE WIRELESS DYNAMICS SENSOR SYSTEM (WDSS) The Vernier Wireless Dynamics Sensor System (WDSS) transfers data to a computer using Bluetooth, a...
- https://www.vernier.com/til/4429/
- How good is the time sync between WDSS and other interfaces?
- Or, a broader question is “How do the data from the WDSS and Motion Detector compare? Both will display acceleration values.” The sync between the...
- https://www.vernier.com/til/1576/
- Davis Instruments Troubleshooting and FAQs
- As of January 2025 Vernier Science Education no longer sells Davis Instruments products. For help with Davis Instrument products see below: Davis Support Web Page:...
- https://www.vernier.com/til/2515/
- How do you use the current and voltage controls of the Extech Power supply?
- The can operate in either voltage-control or current-control modes, and so has both current and voltage control knobs. Most instructors are familiar with power supplies...
- https://www.vernier.com/til/1825/
- How can I check to see if my Power Amplifier power supply is working?
- The power supply for the Power Amplifier is an unusual double power supply. If you look at the connector which plugs into the Power Amplifier,...
- https://www.vernier.com/til/3938/
- Bluetooth Wireless FAQs
- For instructions on how to connect Go Direct sensors via Bluetooth® wireless technology, see General Bluetooth Questions Q: What is Bluetooth? A: Bluetooth...
- https://www.vernier.com/til/1611/
SAVE/SHARE YOUR CART