Search
Electrode Support- Data Collection with Go Wireless pH/Electrode Amplifier FAQs ...
- Jul 13, 2017 ... 3, you can connect to up to 8 Go Wireless pH sensors at one time. This is limited by the number of meter screens we support. With LabQuest App ...
- https://www.vernier.com/til/3375
- Go Wireless pH Troubleshooting and FAQs - Technical Information ...
- Aug 13, 2018 ... –The pH electrode I have been using no longer seems to work or is ... support Bluetooth low energy technology. For more detail, see Go ...
- https://www.vernier.com/til/3272
- What are the dimensions of the Go Direct Optical Dissolved Oxygen ...
- Oct 31, 2019 ... It is compatible with the Primary Productivity Kit (PPK), Water Quality Bottles (8 bottles) (WQ-BOT), and the Electrode Support (ESUP). It ...
- https://www.vernier.com/til/4228
- My pH probe does not give an accurate reading. What should I do ...
- Oct 16, 2014 ... You get more stable readings when you stand the pH sensor in an electrode support or clamp. 2. An important indicator of the viability of a ...
- https://www.vernier.com/til/3311
- How do I use the Ethanol sensor with a CO2 Gas sensor to measure ...
- Nov 16, 2018 ... Important: Use a ring stand and a clamp or electrode support to secure the sensor. Adjust the sensor so that the tip of the sensor is one cm ...
- https://www.vernier.com/til/2862
- What sensors are supported by Go Wireless Link when using ...
- Jan 21, 2020 ... Graphical Analysis GW and Graphical Analysis app (version 2.3.1 – 4.0.3) for iOS supports data collection with the Go Wireless Link sensor ...
- https://www.vernier.com/til/3429
- The pH electrode I have been using no longer seems to work or is ...
- Sep 11, 2018 ... If your pH Sensor is reading slightly off of the known buffer pH (eg, reads 6.7 in a buffer 7), you may simply need to calibrate the sensor.
- https://www.vernier.com/til/730
- Nitrate Ion-Selective Electrode Troubleshooting and FAQs ...
- Feb 6, 2015 ... Primary Test: Check the raw voltages while calibrating in the standards. The high (100 mg/L) should be around 1.6 volts. The low (1 mg/L) should be around 2.4Â ...
- https://www.vernier.com/til/1432
- General tips for using Ion Selective Electrodes (ISE). - Technical ...
- Jan 25, 2019 ... If, after implementing all of these tips, you are still unable get your ISE to function properly, contact Vernier Tech Support at (888) 837Â ...
- https://www.vernier.com/til/665
- Platinum Cell Conductivity Probe Troubleshooting and FAQs ...
- Sep 29, 2015 ... For best results, condition the electrode in a standard solution for three to five minutes prior to use. -Minimum software version: Logger ...
- https://www.vernier.com/til/3477
- I am using a third-party electrode with your Electrode Amplifier. How do I calibrate the electrode in Logger Pro 3?
- NOTE: The 3rd-party electrode must have a BNC connector at the end of its cable to connect it to the Electrode Amplifier. Also, you’ll need...
- https://www.vernier.com/til/2459/
- I found an ORP electrode that was stored dry. How can I test it to see if the electrode is still working?
- The ideal test solution for an ORP electrode is a commercially-produced standard. Many companies sell ORP standards: Hach, Cole Parmer, and Hanna are three examples....
- https://www.vernier.com/til/2467/
- The glass bulb of my pH Sensor is broken. Can it be repaired?
- No, unfortunately a broken glass bulb on any of our pH sensors cannot be repaired or replaced and is not covered by the warranty. We...
- https://www.vernier.com/til/782/
- What is the best way to clean the glass bulb of the pH electrode?
- Generally, rinsing the electrode with distilled water after using should suffice. If the glass bulb looks dirty, you can rinse the electrode with warm water...
- https://www.vernier.com/til/706/
- Can I use my third-party ISE with my Vernier equipment?
- Maybe. The answer to this depends on a couple of things. 1. Does your electrode have a BNC connector? If so, you can use it...
- https://www.vernier.com/til/2291/
- Can I use a Vernier BTA ISE with Arduino?
- We do not recommend this combination due to the nature of the sensor and complexity of continuous need for calibration. However, we have done this...
- https://www.vernier.com/til/3635/
- How can I have my ISE read mV output instead of mg/L?
- For Go Direct ISEs (order codes begin with GDX-), simply enable the sensor’s mV channel in the app. For most LabQuest ISEs (order codes end...
- https://www.vernier.com/til/1296/
- How can I keep my pH or ORP storage solution from spilling when the sensor is in use?
- After removing the sensor but before screwing the cap back on the storage solution bottle, place a nickel under the cap and screw the cap...
- https://www.vernier.com/til/728/
SAVE/SHARE YOUR CART